Model Name: WRT54G3G

V2.00.22 (2006/11/27)

Add items:
===================================================
1. Add Huawei E618 supported.
===================================================

Fixed items:
===================================================
- Fixed => E39, During heavy downloads, the Hauwei cards E618/E620/E630 sometimes show signal strength as 'No Signal', whilst the signal is evidently fine as router is transferring data at full card throughput. Before and after the refresh containing 'No Signal', the strength was 'Good' or 'Excellent'.
- Fixed => E40, Colt card has strange behaviour with regard to manual network selection. After manual network search, the search list is populated with the expected results, except that the home network is only marked 'available' not 'current' and the radio button is not preselected. If the radio button next to the home network is selected and OK is pressed, the 'system processing' screen is shown as expected, after which the user returns to 'basic setup'. The connect button here is greyed out and the network name is always 'Acquiring', no connection is possible until reboot of router.
- Fixed => E41, Connection lost shortly after download initiated. The router drops the mobile connection and flashes the Power LED. I have seen this on Colt, QuadLite, Nozomi & U630 cards, and two routers
- Fixed => E42, Setup page, This is apparent with Hauwei E620/E630 when first accessing the Setup page after reboot. The Connect button is greyed out until 7..10 refreshes have taken place (45 seconds or so), other cards typically are available after one or two refreshes. 
- Fixed => E43, After making a mobile connection the router is allowed to idle for a long period of time(1 hour +). The connection drops, and later the user is unable to remake a connection without rebooting the router. 
- Fixed => E45, Hauwei E630 perfomance on 3.6Mbps network unacceptable. Currently achieves around 1.4 Mbps. 
- Fixed => E46, Failure to reconnect after successful connection is terminated. Mainly seen with the GT 3G Quad card but happens with Huawei as well.  
- Fixed => E47, Seems to be a contextual mixup between PPPoE connect button and mobile network connect function resulting in ?can't get an IP from 3G/UMTS network? while connecting in PPPoE.
- Fixed => E50, When using fixed WAN in PPPoE mode and the mobile connection is brought up in preference, the traffic is not routed through the mobile network as it should be.

===================================================
- Modified => After push connect or disconnect or OK or Select Network button should be greyout until action finished.
- Modified => Select Network GUI page if user push "OK" to set operator after process finished then close this page.
- Modified => Vodafone branded Huawei E620 worked. 
- Modified => If search network timeout then display "Timeout !!" information. 
- Modified => After pressing "Search" on the manual network selection form make it go away.
-Modified => Make sure the card changes its bearer affinity when commanded by the GUI, not just at startup.

===================================================
- Modified => E32 After pressing OK on the manual network selection form make it go away.
- Modified => E34 Make sure the card changes its bearer affinity when commanded by the GUI, not just at startup.
- Modified => Change Huawei datacard(E618,E620,E630) query status period parameter.
When router boot up query period is 12 sec. after 1 min. change query period to 30 sec.       
- Modified => When Huawei datacard(E618,E620,E630) connected, not use "AT+COPS=0,0" and "AT^SYSCFG" AT commands to query status.

===================================================
- Modified => Change Huawei datacard(E618,E620,E630) query status period parameter.
When router boot up query period is 12 sec. after 1 min. change query period to 60 sec. To avoid sometimes query cause Huawei datacard no response.  

===================================================
- Fixed => E11, Network search listing shows "unknown" for test plant UTRAN instead of displaying the network ID (26889)
- Fixed => E12, Network search and selection works for network 26889 but HTML "Connect" button is not enabled and network
is listed as Unknown (or Acquiring).
- Fixed => Change service to GPRS only or UMTS only datacard is not change to correct service. 

===================================================
- Fixed => The LED has a blinking problem when datacard is still searching the service provider.
- Modified => keepalive behavior ??The router redial within 5 seconds of a failed attempt."

===================================================
- Fixed => Set Auto Connect to Keep Alive then using front button to disconnect 3G network. Router can't reconnect to 3G network anymore.
- Modified => Set a subnet mask suitable for CIDR network prefixes in the whole range /8, down to /30.
- Modified => Sometimes Pin Code already input successful but Router still show "This SIM requires a PIN to unlock".

===================================================
- Fixed => When no SIM inserted GUI alert "SIM busy",it should alert "No SIM".
- Fixed => Keep Alive mode : When Pin Code is incorrect auto dial mode stop until Pin Code is unlock.
- Modified => Keep Alive mode : When ppp interface status is down, kill pppd process and enter redial mode. 
- Modified => Keep alive mode : before auto dial to internet need to check Operator is avaliable.
- Modified => If "Service" select "GPRS only" or "UMTS only",when connecting "Mobile Network Bearer" Show the state chosen(Service).

===================================================
- Fixed => The color of the LED is inaccurate as connect success.
- Fixed => Power&3G LED are blinking at the same time if auto connect enabled when power on.
- Modified => GUI 3G status refresh time changes from 1 minute to 20 seconds on Setup page.
- Fixed => Sometimes Hardware connect/disconnect button doesn't work.

===================================================
- Fixed => E5, When set to UMTS-preferred but router can only acquire GPRS due to bearer availability, the 3G/UMTS-LED on the front panel flashes blue (correct) but becomes solid blue immediately after connect(incorrect). The LED can take upto one minute before it turns solid green.

- Fixed => E24, Hauwei E618 card is crashing the router during downloads.
- Fixed => E26, Novatel U630 and U740 only returning one entry during network search function.
- Fixed => E27, Hauwei E630. Setup and status pages display model string 'E630', but should display 'Hauwei E630'.
- Fixed The network name for SmarTone-Vodafone in the Web UI is not correct(see attachment file), to be changed from SmartTone to SmarTone-Vodafone.?? (>>>> SmarTone is single T<<<<)
===================================================

- Fixed => E25, Hauwei E620 & E630. Not displaying network name in setup and status pages, but using network number instead.

===================================================
- Fixed => E1, Auto-Connect Keep Alive Mode does not reconnect the to the mobile network if?the signal is dropped for any reason.This is difficult for us to reproduce in our test labs as they all, by their nature, have constant strong signals.

- Fixed => E2, Auto-Connect, Connect on Demand function requires an initial connection to be physically made before the function works. But more importantly, it also does not work after a power re-cycle.

- Fixed => E6, No ability to specify a non-class C address range for DHCP
- Fixed => E8, Support Hauwei E630 card
- Fixed => E14, Prepaid APNs need adding to the manual selection list in the Web GUI. Automatic selection to still select correct contract APN as default
- Fixed => E18, No ability to specify a non-class C address range for LAN interface. You cannot currently set the router's subnet mask to anything other than a subnet derived from a class C range. This limits the integration of the router in a corporate environment.
- Fixed => E21, Using default out-of-the-box settings. LB not connected to 3G or WAN. Setup page shows Disconnected and Connect button is available. Go to the Wireless page and change "Mixed" to "Disable" to switch off WLAN. Click Save settings. Return to Setup Page, Status is Disconnected and 3G button is greyed out. Button remains greyed out for about one minute (3 or 4 refreshes can be seen during this time).
- Fixed => E22, Huawei E620 & E630. Not functioning properly. ??PINCODE is locked, can't update status??
- Fixed => E23, Option Colt, not returning any results during network search whilst in 3G-preferred  and 3G-only modes.
- Fixed => E15, Novatel U740 does not display bearer type in network search.
- E19 => The status display with Novatel U630 & U740 cards is unreliable. Sometimes the network is displayed as 'Acquiring' even though a connection is active and functioning correctly.
- Fixed => E20, Router displays a misleading message(??No 3G/UMTS SIM inserted, please insert your SIM Card!??) indicating wrong PIN on Power Up even if no PIN entered.

- Fixed => Keepalive called from one of the closed source bits issue.



===================================================

v1.99.8 (2006/05/19)

Initial Release
-Support Huawei E620.
-Support Novatel U740. 
-Support Option GT 3G+ (Nozomi).
-Support Option 3G QUAD.
-Support Option GT 3G 
-Support Novatel U630..


