Linksys, A division of Cisco Systems, Inc.


Product:           WAG200G Annex A 

Classification:    Firmware Release History

Release Date:      13 Mar, 2009

Firmware Version:  1.01.09 (ETSI)

Language:	   Multi-language

Note: Not to be used with Annex B models (DE and E1)
____________________________________________________________

Revision history
SW version:1.01.09
Release Date: 06/13/2008
Based on: 1.01.08(03)
1.	Same as 1.01.08(03) but version updated to 1.01.09.

SW version:1.01.08(03)
Release Date: 05/23/2008
Based on: 1.01.08(02)
1.	Fix When WAN is PPPoA and ATM QoS is VBR, then no access to GUI after DSL link is up.
2.	Fix Make WAG200G receives 8 PADOs from network side, and check PPP connection comes up. It fails.
3.	Fix Run setup wizard to configure DUT cause DUT can't get DNS in Status.htm.

SW version:1.01.08(02)
Release Date: 04/24/2008
Based on: 1.01.08
1.	Fix GUI Setup_DDNS.htm show incorrect;
2.	Fix ARP reply packet include pppoe information;
3.	Update DSL datapump to 7.04.03.

SW version:1.01.08
Release Date: 04/02/2008
Based on: 1.01.07
1.	Fix pvc auto detect not working;
2.	Fix Multicasting not working at LAN side after a few minutes later;
3.	Fix GUI Status>DSL Connection page shows always MultiMode in DSL Modulation Mode.

SW version:1.01.07
Release Date: 03/20/2008
Based on: 1.01.06
1.	Support ADSL2-Annex-L and Add ADSL2-Annex-L select in all language GUI;
2.	DSL Datapump update to version 7.02.03.00;
3.	Support Annex M.
4.	Fix VPN passthrough ipsec response packet force port 500.
5.	Fix when NAT & Firewall are disabled,can’t access from WAN side to LAN pc issue..
Inzoo Lee’mail about“Description: Though NAT and Firewall are disabled, there is no access from WAN side to LAN pc.( 2007-12-21)
Steps to reproduce:
	do factory default
	set wan to PPPoA, and put correct credentials. get WAN interface up.
	Disable NAT in advanced routing, and Firewall protection in Security>Firewall. Also uncheck 'block anonymous internet requests'.
	put static route on WAN router(PPP server), so that WAN PC(or WAN router) can access local network which is behind WAG200G.
	Ping from WAN to LAN PC. 
	Ping doesn't work.
I tried to access other services(HTTP, FTP etc) from WAN to LAN, but no access.
When pactured  packet on WAN side, packets are NATed correctly. But WAG200G still blocks all the service requests from WAN side.
If port forwarding is enabled, then service(ftp, http) works.”
6.	Fix Heavy UDP traffic causes WAN connection disconnected issue.
Inzoo Lee’mail about“After WAN is up, over-subscribe traffic.( for example 2M for up stream for 8M/1M DSL connection. WAN goes down as WAG210G doesn't receive Echo reply for more than 3 times.”

SW version:1.01.06
Release Date: 08/09/2007
Based on: 1.01.05(01)
1.	Fix XSS and CSRF security issue
2.	Fix Upnp hang and crash issue.
3.	Closed 5190,5566,4443 ports which is open for old AIM/MSN protocol
4.	Fix When p2p software running long time, DSL performance will downgrade issue.
5.	Use new linksys logo 
6.	Add Single Port Forwarding entries to 20.
7.	Move language selection below firmware Upgrade.
Karl’s mail about “WAG200G setup wizard bugs”, in doc “WAG200G Setup Wizard and Firmware Bugs.doc” 2007-08-07.
8.	Add Access Restriction solution.
    Robert’s mail about ” RE: Sercomm weekly status meeting agenda on 8/6” 2007-08-09

SW version:1.01.05(01)
Release Date: 06/15/2007
Based on: 1.01.05a
   1.  Use new linksys logo.
   2.  FIX bug [WAG200G A FW 1.01.05a Buglist.xls(13-Jun-07)] as follows:
a).Fix [PKI] PPTP server behind WAG200G not working issue.
b).Fix ‘Management’page allows saving without a username or password entered issue.

SW version:1.01.05a
Release Date: 06/06/2007
Based on: 1.01.05
1.	Update help page about “Syslog” option.
2.	add 3 more portmapping for Wizard TRUE function.   
3.	Fix Basically WAN doesn't work after unplug/plug back DSL cable.
4.	Update new Cisco logo.  

SW version:1.01.05
Release Date: 05/24/2007
Based on: 1.01.04
1.	Karl’s WAG200G Firmware Corrections(2007.05.16), as follows:
a)	Limit wireless channels to 1 through 11 for Brazil. 
b)	Default settings for Brazilian Portuguese should be GMT-3:00, PPPoE, LLC, 0, 35, Keep Alive
c)	Include Windows time zones
d)	Include time zones and settings for other languages
2.	Karl's "WAG200G Firmware Corrections v1.01.04.doc"(2007/05/18).
a)	Add language option in “Setup” page.
b)	Fix Portuguese(Brasil) UI display issue.
3.	Add Brazilian Portuguese language support.
4.	Add help for Reboot page.
5.	Update help page. 
6.	Wizard security issue.
7.	Fixed 120dpi issue in UI.
8.	Avoid rebooting when user change settings in 'Basic Setup' and ‘Management’ page
9.	Remove Enable/Disable Wizard function from UI.
10.  Change “Logviewer” to “Syslog” in Web UI and Help Pages


SW version:1.01.04(06)
Release Date: 05/22/2007
Based on: 1.01.04(05)
1.	Karl’s WAG200G Firmware Corrections(2007.05.16), as follows:
	Limit wireless channels to 1 through 11 for Brazil GMT-10:00 through GMT-3:00 
	Default settings for Brazilian Portuguese should be GMT-3:00, PPPoE, LLC, 0, 35, Keep Alive
	Include Windows time zones
	Include time zones and settings for other languages
2.	Karl's "WAG200G Firmware Corrections v1.01.04.doc"(2007/05/18).

SW version:1.01.04(05)
Release Date: 05/18/2007
Based on: 1.01.04(04)
1.	Add language option in “Setup” page.
2.	Fix Portuguese(Brasil) UI display issue.

SW version:1.01.04(04)
Release Date: 05/15/2007
Based on: 1.01.04(02)
1.	Change UI language option with Portuguese(Brasil).
2.	Add help for Reboot page.
3.	Update help page. 

SW version:1.01.04(02)
Release Date: 05/10/2007
Based on: 1.01.05
1.	Fixed UI switch Brazilian Portuguese language issue. 
2.	Add ping Brazilian Portuguese language support.

SW version:1.01.04(01)
Release Date: 04/05/2007
Based on: 1.01.04
   1.  Add TXT file config function.

SW version:1.01.04
Release Date: 04/05/2007
Based on: 1.01.03(06)
1.	Use old datapump with version 5.00.02.00.
2.	Change language option of each country.
3.	Add Setup Wizard mutillanguage display in UI.
4.	Change default values as linksys ODM checklist.
5.	Fix UI translation issue about Setup Wizard help.

SW version:1.01.03(06) Beta Version
Release Date: 03/29/2007
Based on: 1.01.03(05)
   1.  Add Enable/Disable Wizard function in UI.

SW version:1.01.03(05) Beta Version
Release Date: 03/27/2007
Based on: 1.01.03(04)
   1.  Add FSM for fix wizard security issue.

SW version:1.01.03(04) Beta Version
Release Date: 03/15/2007
Based on: 1.01.03(03)
1.	Fix wizard security issue.
2.	Fix IPSec passthrough issue(AT&T VPN client can’t connect the VPN server).

SW version:1.01.03(03) Beta Version
Release Date: 03/15/2007
Based on: 1.01.03(01)
1.	Update ATM driver version to 7.02.01.00.
2.	Update DSL HAL version to 7.02.01.00.

SW version:1.01.03(01) Beta Version
Release Date: 03/05/2007
Based on: 1.01.03
1.	Update datapump to version 7.02.03.

SW version:1.01.03
Release Date: 02/13/2007
Based on: 1.01.02(01)
    1.Fix UI display issue.

SW version:1.01.02(01) Beta Version
Release Date: 02/08/2007
Based on: 1.01.02
    1.Change ADSL driver as same as FW version 1.01.01.

SW version:1.01.02
Release Date: 01/30/2007
Based on: 1.01.01(03)
1.	Add CD swap language function support.

SW version:1.01.01(03) Beta Version
Release Date: 01/26/2007
Based on: 1.01.01(02)
1.	Fix UI upgrade can’t reboot.
2.	Fix When Setup up PPTP Server on LAN interface of DUT and enable PPTP Passthrough. Attempt to connect from a PC on the WAN interface to the PPTP server on LAN interface of DUT via WAN IP address issue.
3.	Fix somes UI display issue.

SW version:1.01.01(02) Beta Version
Release Date: 01/11/2007
Based on: 1.01.01(01)
1.	Update ADSL driver.

SW version:1.01.01(01) Beta Version
Release Date: 01/03/2007
Based on: 1.01.01
1.	Fix On the router status page the WAN is connected, but the "disconnect" button is grayed out and customers cannot break the connection manually
2.	Fix Remote Management will not work if WLAN is disabled.
3.	Fix the router will not accept (.) or a dash characters for Email Address for Alert Logs and Return Email.

SW version:1.01.01
Release Date: 11/29/2006
Based on: 1.01.00a
1.	Fix wizard set language issue.
2.	Consummate GUI select language function for factory production. 

SW version:1.01.00a
Release Date: 11/20/2006
Based on: 1.01.00
3.	Fix can’t connect in Indonesia us PPPoE----[1.01.00(03) Beta version]
4.	Fix Port blocking check port issue----[1.01.00(04) Beta version]
5.	Remove telnet server for debug.

SW version:1.01.00
Release Date: 10/19/2006
Based on: 1.00.10a
1.	When Wan disconnect and then connect ,add warning message "We have just avoided a PPPReceivedTerminate right now..." to log file.
2.	Fixed port blocking issue in Access Restrictions configuration page.

SW version:1.00.10a
Release Date: 9/11/2006
Based on: 1.00.10
1.	Fix Cookie issue.

SW version:1.00.10
Release Date: 9/11/2006
Based on: v1.00.09a
2.	Change firmware name.
3.	Disable LCP request echo and deal with WAG200G "DSL line dropping and reconnecting".
4.	After refreshing incoming or outgoing log pages, the list goes to ALL logs.
5.	Cange "pageRefresh" botton to "Refresh" only.

SW version:1.00.09a (Bata version)
Release Date: 7/28/2006
Based on: v1.00.08
1.	Add incoming and outgoing logs.

SW version:1.00.08 (Bata version)
Release Date: 7/25/2006
Based on: v1.00.07d
1.	Fixed WEP bug in buglist of v1.00.07
2.	Fixed Connect on Demand problem as WAG300N(buglist of v1.00.07)
3.	Add the hidden page of DSL information

SW version:1.00.07d (Bata version)
Release Date: 7/21/2006
Based on: v1.00.07c
1.	Fixed firmware can’t be upgrade via http.

SW version:1.00.07c (Bata version)
Release Date: 7/12/2006
Based on: v1.00.07a bata2
2.	Fixed WEP key 2 allowed to enter 13 digits

SW version:1.00.07a (Bata2 version)
Release Date: 7/7/2006
Based on: v1.00.07a bata1
1.	Fixed WEP key

SW version:1.00.07 (Bata1 version)
Release Date: 6/23/2006
Based on: 1.00.06
1.	Add rebooting code when WAG200G buffer over-flowing.

SW version:1.00.07
Release Date: 6/23/2006
Based on: 1.00.06
1.	Fix mtu setting under PPPoA and PPPoE wan mode
2.	Fix when disconnect in PPPoA , led can’t turn off.
3.	Fix wireless Http upgrade fail.
4.	Fixed PPPoE and PPPoA can't get ip.
5.	Change same help pages display error.
6.	WEP 128bit generate 4 differnet keys
7.	Support Samsung’s flash
8.	Fixed pppoe “Dial on Demanded” mode auto connect after idle timeout

SW version:1.00.06
Release Date: 5/26/2006
Based on: 1.00.05
1.	Fix NTP send packet out when idle time out.
2.	Correct WEP 128 bit generating 4 different keys.

SW version: 1.00.05a (Bata version)
Release Date: 5/17/2006
Based on: v1.00.05
Change list :
1.	Correct 128-bit WEP serious to generate to the different 4 keys.

