Linksys- A Division of Cisco System, Inc.

Firmware Date	 : January 15th 2004
Current Firmware : Version 1.0.11
Product Part No  : RV082
----------------------

RV082 Firmware Revision History

v1.1.1		2004/03/17

1.	Solve the DPD (Dead Peer Detection) interoperability problem with CISCO IOS
2.	MTU implementation changed as follows:

	(1)	<PPPoE is On & MTU=AUTO>
-	RV082 should be adjusted the MTU to Specified MRU size which is known through PPP negotiation.
-	If no notify MRU from the Peer, it should be 1492bytes as default.
-	If IPSec is used on PPPoE, set MTU size Current MTU- 60 bytes as default if PPPoE is used in conjunction 	with IPSec.
	(2)	<DHCP is On & MTU=AUTO>
-	If No Active IPSec tunnel, MTU should be 1500 automatically as default.
-	If There is Active IPSec Tunnels, set MTU size Current MTU- 60 bytes as default.
-	Affect above behavior to following case.
					>DHCP
					>Static Address
3.	Decrease the NAT aging time.
 		Purpose: To avoid the WAN connection dropped due to NAT table full

v1.1.0		2004/03/03
	1.	Fixed a bug that Factory Default function did not work in v1.0.12 only  
	2.	Modify the IPSec Keep-alive and connect-on-demand functions internally.
		Purpose: To reduce the overhead of RV082 system

v1.0.12		2004/02/18
	1.	Solve a problem that Microsoft trace route(tracert) did not pass through
		RV082.
	2.	Solve a problem that failed to use XDCC transfer in IRC software.
	3.	Support DPD(Dead Peer Detection) functionality.
		Note: Dead Peer Detection(DPD) is a mechanism used to detect a dead 
		IKE peer. When DPD is enabled, and only if both peers provide DPD mechanism, periodic HELLO/ACK 		messages will be sent through the tunnel in order to prove liveliness. Once a dead peer found, RV082 		will disconnect the tunnel so that connection can be re-established if needed. The DPD message 		interval can be changed from the Interval field. (Reference document: draft-ietf-ipsec-dpd-04.txt)


v1.0.11		2004/01/15
1.	Support "NAT Loopback" functionality. 
	Purpose: It allows LAN-side users accessing LAN-side server by 
	typing WAN IP address.
2. 	Support IPSec interoperability with SSH Sentinel VPN Client in both Main and 			Aggressive 	modes.  Purpose: It allows users using SSH client to connect to RV082 		through Group VPN 	tunnel(Aggressive mode).
	Note: Older firmware worked with SSH only in Main mode. 
3.	Web-UI modification:
	Added 3 pre-defined service ports, PPTP(1723), IPSec(500) and 
	L2TP(1701), in Service list on the "Setup -> Forwarding" screen.
	Purpose: It allows user to host PPTP server at LAN network by   	   	configuring this Forwarding page.


v1.0.10		2004/01/06
1.	Support NetBIOS over IPSec functionality
2.	Web-UI modification:
	Added NetBIOS broadcast option on VPN Advanced page.
	Note: the default setting is Disabled
	Modified on-line help contents for NetBIOS broadcast option

v1.0.9		2004/01/01

1.	Fixed following Web-UI bug that only existed in v1.0.8:
	On DHCP Setup page, DHCP server can not be disabled

2.	Web-UI modification:
	Added on-line Help contents about Microsoft XP/2000 VPN Client on Client to 			Gateway(Group VPN) help page.


v1.0.8		2003/12/24

1.	Web-UI modification: Add Static IP setting on DHCP Setup page. 
	Add DNS Server setting on DHCP Setup page.
	Add Microsoft XP/2000 VPN Client option on VPN Client to Gateway GroupVPN 			setting page.	

		Note: This option is used for Dynamic IP (e.g. PPPoE or DHCP) users which 		using Microsoft VPN client. The difference between Microsoft and other VPN client 		is that Microsoft client does not support Aggressive mode and FQDN/UserFQDN ID 			options. Add/Modify on-line Help contents on DHCP and Port Management pages.


v1.0.7		2003/12/02

1.	Modified the UPnP function for passing the test of UPnP Certification Test 
	Tool

v1.0.6		2003/11/26

1.	Solved an IPSec interoperability problem with Cisco VPN Concentrator. To accept 		more UDP/TCP ports when IKE Phase-1 negotiation
2.	Solved a problem that some kind of PPPoE password may be saved as incorrect value 		under Windows2000/98 environment. 
3.	Fixed a bug that SNMP sysUpTime did not report the correct time.
4.	Web-UI modification:
	Enlarge the max. length of PPPoE username/password settings from 20 to 60 			characters
	On Advanced Routing page, allow users to modify the value of Destination IP on 		exist entry. (This style are applied on all of the pages which use Add to list 		button)
5.	DHCP server modification: 
	Do not assign unused IP address to client

v1.0.3		2003/10/17

1.	Add internal check points for auto-test use. It is only used at manufacturing 	stage.
2.	Change the default snmp sysName from RV082_<random mac> to RV082_<LAN_mac>
3.	Initialize the phrase of snmp sysDescr as RV082 VPN Router
