************** 7BESH IPMI2.0 Firmware Release History*****************
---------------V0.01---------------------------04/11/2006
Feature Implemented:
        - Building threshold and digital sensors.
        - Building first release of FRU.
        - Building first release of SDR.
File distributed:
        - Firmware Image: 7BESH001.BIN
        - SDR Image: 7BESH001.SDR
        - FRU Image: 7BESH001.FRU
---------------V0.02---------------------------04/26/2006
Feature Implemented:
        - Remove OEM SEL
          -> External Rack, Correctable ECC, Uncorrect ECC, Memory Spare, MemErrLogDisable, POST Error, Parity Error,
             System Error, Sys Reconfigur, OEM System Boot, OS Boot, Memory Resize, BusUncorrectable, Fatal NMI, CPU1,
             CPU2, MP table failure
File distributed:
        - Firmware Image: 7BESH002.BIN
        - SDR Image: 7BESH002.SDR
        - FRU Image: 7BESH001.FRU
---------------V0.03---------------------------05/22/2006
Feature Implemented:
        - Modify when Get SDR length > 30 it always return 0xCA, and Get FRU array.
        - Fixed Get SDR Info and Get SEL Info cant return correct add time and erase time.
	  - SEL add time    0x7000
	  - SEL erase time  0x7004
          - SDR add time    0x7008
	  - SDR erase time  0x700C
        - Fixed PowerOn, PowerOff can't work issue.
        - Fixed can't OpenSession 
          - We find it not check Payload Type bit 7 in AMI code.
            If the bit 7 is set, BMC not need CONF_AES_CBC_128 encrypt.
File distributed:
        - Firmware Image: 7BESH003.BIN
        - SDR Image: 7BESH003.SDR
        - FRU Image: 7BESH001.FRU

---------------V0.04---------------------------06/01/2006
Feature Implemented:
        - Fixed when DC off, DC on Sensor Reading can't return correct value.
        - Release new SENSEL Utility version 0.34.
File distributed:
        - Firmware Image: 7BESH004.BIN
        - SDR Image: 7BESH003.SDR
        - FRU Image: 7BESH001.FRU
---------------V0.05---------------------------06/09/2006
Feature Implemented:
        - Modify ID LED(GetChassisIdentify) function.
        - Remove Systemp1, 2 and addition back plant sensor.
        - Modify Set MAC Address function write to EEPROM.
File distributed:
        - Firmware Image: 7BESH005.BIN
        - SDR Image: 7BESH004.SDR
        - FRU Image: 7BESH001.FRU
---------------V0.06---------------------------06/16/2006
Feature Implemented:
        - Fixed when syeten reset, BMC can't detect CPU tempature.
        - Fixed back valtage 12VC and 12VD return incorrect value.
        - Modify Fan redundant function.
        - Modify Getsyetem GUID use MAC address.
          - 32556C2E-1001-4abc-8CD5-xxxxxxxxxxxx
        - Modify SOL function and to set EMP_S0 at high.
File distributed:
        - Firmware Image: 7BESH006.BIN
        - SDR Image: 7BESH005.SDR
        - FRU Image: 7BESH001.FRU
---------------V0.07---------------------------06/21/2006
Feature Implemented:
        - Fixed can't flash SDR.
        - Fixed when with back plant, SuperIO will detect incorrect value.
File distributed:
        - Firmware Image: 7BESH007.BIN
        - SDR Image: 7BESH006.SDR
        - FRU Image: 7BESH001.FRU
---------------V0.08---------------------------06/29/2006
Feature Implemented:
        - Modify FanSpeedControl function.
        - Changed slave address to 0x20, Channel number to 0x00.
	- Changed product name to Altos G540.
File distributed:
        - Firmware Image: 7BESH008.BIN
        - SDR Image: 7BESH007.SDR
        - FRU Image: 7BESH002.FRU
---------------V0.09---------------------------07/06/2006
Feature Implemented:
        - Fixed voltage can't detect issue.
        - Remove FAN_F1 and FAN_F2 in the SDR.
        - Change chassis information type to show Tower in the FRU.
File distributed:
        - Firmware Image: 7BESH009.BIN
        - SDR Image: 7BESH008.SDR
        - FRU Image: 7BESH003.FRU
---------------V0.10---------------------------07/14/2006
Feature Implemented:
        - Remove Back_Fan1 and Back_Fan2 sensor.
        - Fixed sometime 12VC and 12VD return 1 issue.
        - Fixed CPU 1 Temp 2 detect incorrect value issue.
        - Fixed CPU Fan speed was too slow.
        - Change System Temp uses Diode mode.
        - Fixed when BMC enent lot was happen, SOL function did not work.
File distributed:
        - Firmware Image: 7BESH010.BIN
        - SDR Image: 7BESH009.SDR
        - FRU Image: 7BESH003.FRU
---------------V0.11---------------------------07/20/2006
Feature Implemented:
        - Remove FUSE sensor.
        - Remove HDD State sensor.
        - Fixed voltage show incorrect value and support SIO IT8718.
        - Release new SENSEL utility 0.35
File distributed:
        - Firmware Image: 7BESH011.BIN
        - SDR Image: 7BESH010.SDR
        - FRU Image: 7BESH003.FRU
---------------V0.12---------------------------07/27/2006
Feature Implemented:
        - Modify when SOL activate, set GPIO EN_S1 to low.
        - Changed Maximun SOL retry is 100.
        - Fixed only one user available in BMC User setting.
          - Enable user:
            KCS 18 43 D1 xx 04 00
          - Disable user:
            KCS 18 43 81 xx 0F 00
          - Get user access:
            KCS 18 44 01 xx
            xx --> ID
File distributed:
        - Firmware Image: 7BESH012.BIN
        - SDR Image: 7BESH010.SDR
        - FRU Image: 7BESH003.FRU
---------------V0.13---------------------------08/04/2006
Feature Implemented:
        - Fixed fan redundant sometime was not work.
        - Fixed woodcrest CPU temperature was show error.
        - Fixed moninal value show 0 or NA in ASM utility.
        - Update Fanspeedcontrol V0.4.
File distributed:
        - Firmware Image: 7BESH013.BIN
        - SDR Image: 7BESH011.SDR
        - FRU Image: 7BESH003.FRU
---------------V0.14---------------------------08/16/2006
Feature Implemented:
        - Fixed CPU 1 Temp 2 show 0 error in woodcrect
        - Fixed only one user available in BMC User setting issue.
        - Update Fanspeedcontrol V0.5.
File distributed:
        - Firmware Image: 7BESH014.BIN
        - SDR Image: 7BESH011.SDR
        - FRU Image: 7BESH003.FRU
---------------V0.15---------------------------08/29/2006
Feature Implemented:
        - Fixed IPMB bus was no response issue
File distributed:
        - Firmware Image: 7BESH015.BIN
        - SDR Image: 7BESH0011.SDR
        - FRU Image: 7BESH003.FRU
---------------V1.00---------------------------09/14/2006
Feature Implemented:
        - Change fan redundant the critical RPM to 1900 that all fan set to maximun.
File distributed:
        - Firmware Image: 7BESH100.BIN
        - SDR Image: 7BESH100.SDR
        - FRU Image: 7BESH100.FRU
---------------V1.01---------------------------09/15/2006
Feature Implemented:
        - Change fan redundant the critical RPM to 1700
File distributed:
        - Firmware Image: 7BESH101.BIN
        - SDR Image: 7BESH100.SDR
        - FRU Image: 7BESH100.FRU
---------------V1.02---------------------------09/21/2006
Feature Implemented:
        - Remove ID LED function.
        - Set SYS_FAN cricial RPM to 1700.
File distributed:
        - Firmware Image: 7BESH101.BIN
        - SDR Image: 7BESH100.SDR
        - FRU Image: 7BESH100.FRU